Name: Stem Ball-ended, Combination Edge & Centre Finder, 0.100in./0.236in./0.250in., Steel
Brand: Kennedy
SKU: KEN5181500K
Price: 2957.08 INR
Availability: InStock

Hand Tools

Measuring & Marking

Centre Finders

Kennedy

Consists of a chuck body and four contact arms. Designed to check ‘run-out’ or concentricity, straightness and alignment. Will indicate the position of a datum point on a component or fixture from the centre line of a machine spindle. Suitable for use on drill presses, lathes, milling machines, borers etc. 

Chuck Body:  
Held in the spindle using a suitable drill chuck or collet chuck (fig 1). The contact arms are retained in position using the knurled collar which lightly clamps the ball joint inside the body. Arms may be exchanged without the need to remove the body from the machine spindle. 

Universal Indicator Holder 
The detachable end will allow clamping with 2 and 3 piece dovetail clamping assemblies and when removed will fit standard 1/4” side clamp. This uses the spindle centre line to align component bores or spigots, check the flatness or squareness of workpieces or fixturing and check run-out of components. The spindle should only be rotated manually to avoid damaging the dial test indicator (fig 1).

Needle Point
To lightly mark out lines and positions on a component as a guide to subsequent operations, using the machine’s dials or digital read-out to position the scriber point (not illustrated). 

Position the contact arm in line, but slightly away from the surface to be aligned. When finding the surface of a diameter, the ‘Disc' must be positioned as near to the centre of that diameter as possible. Run the spindle between 200 and 500 revs/min. The table or spindle is then moved slowly, to bring the contact arm closer to the surface to be aligned. The contact arm will tap lightly against the surface (fig 2) the movement of the arm will become less and less the nearer the datum point gets to the spindle centre line (fig 3). When the arm stops spinning in a straight line and starts to 'jump', this indicates the datum point (fig 4):   
1/2 contact dia + Edge = Centre       
1/2 contact dia - Centre = Edge

Ball Contact  .250”
Used to find a datum  point .125” ± .0005” away from a flat surface.

Disc Contact  .100”  
Used to find a datum point .050” ± .0005” away from a convex surface.

Contents: Chuck Body, Universal Indicator Holder, Needle Point, Ball Contact, Disc Contact.

Comprised of a chuck body and four contact arms, this edge and centre finder set is designed to check 'run-out' or concentricity, straightness and alignment. The components will indicate the position of a datum point on a component or fixture from the centre line of a machine spindle. Suitable for use on drill presses, lathes, milling machines, borers and similar applications.

Features and Benefits
• Ground, hardened and polished contact arms ensure highly accurate centre locating
• Quick change "snap fit" body and arms to easily change your component when needed
• Supplied in a plastic wallet to effectively store and organise your tools
• Unique design universal indicator holder

Contents
• Chuck Body
• Universal Indicator Holder
• Needle Point
• Ball Contact
• Disc Contact

Typical Applications
• Engineering
• Manufacturing
• Workshops

Attribute	Value
Brand	Kennedy
EAN	5036140018792
ECLASS Code	23049190
Overall Length	60 63 65mm
Shank Diameter	0.236in.
Stem Type	Ball-ended
Tip Material	Steel
Tool Type	Combination Edge & Centre Finder
UNSPSC Code	23153013

Kennedy

Stem Ball-ended, Combination Edge & Centre Finder, 0.100in./0.236in./0.250in., Steel

IN STOCK (50+)

Product Information

Product Details

Product Documents

Product Specification

Attribute

Value

Key Information

Group Policies

© 2024 Cromwell. All rights reserved.